Difference between revisions of "ArduPhone"

From Open Hardware Miniconf
Jump to: navigation, search
(Useful AT Commands)
(Useful AT Commands)
Line 42: Line 42:
  
 
'''AT+CSQ''': Check network signal strength. Returns two numbers, comma separated. The first number is signal strength. 0 is no signal, 31 is maximum possible reading. Anything from about 12 up is OK.
 
'''AT+CSQ''': Check network signal strength. Returns two numbers, comma separated. The first number is signal strength. 0 is no signal, 31 is maximum possible reading. Anything from about 12 up is OK.
 +
 +
'''AT+IPR?''': Check current Interface Port Rate (baud rate of the serial port). By default the ADH8066 is set to 115200, but the ArduPhone MCU can't talk that fast while running at 8MHz so the rate has been changed to 9600.
 +
 +
'''AT+IPR=9600''': Set the baud rate. The module will then restart its comms. Don't set this too fast or the ArduPhone MCU won't be able to keep up.

Revision as of 09:16, 22 December 2013

Hardware Assembly Project: ArduPhone

The hardware assembly project this year is designed to be easy for beginners to put together, even if they haven't soldered before, while still resulting in an amazingly cool end result. The ArduPhone design uses mostly surface mount parts which are all pre-fitted, leaving a small number of through-hole parts for you to solder on. You'll need to fit some connectors, solder in some buttons, and clip on some modules that contain most of the functionality pre-assembled and tested, so even if you're a total beginner to hardware hacking you'll end up with a working ArduPhone by the end of the miniconf.

An early prototype and unfitted parts:

PHONE-v1 0-parts.jpg

Prototype with screen, GSM module, buttons, and antenna fitted:

PHONE-v1 0-assembled.jpg

Features:

  • Arduino-compatible: run your own firmware, have 100% control of the phone
  • ATmega1284P MCU running at 3.3V, 8MHz. Custom board profile provided for Arduino IDE
  • Onboard smart LiPo charger
  • Charges from USB (variable charge rate to suit different batteries)
  • 128x128 OLED display
  • ADH8066 GSM module (quad band GSM/GPRS)
  • Microphone and speaker connections for voice calls
  • Send and receive SMSs, and load web pages
  • Arduino headers so you can add more I/O: build it into your own project!
  • PCB can be cut in half to remove keypad

Note: SIM card NOT provided! You can get a pre-paid SIM for the ArduPhone before the conference, or temporarily install your own SIM for testing.

The complete ArduPhone kit will be $110, which includes everything required: main PCB, OLED display module, GSM module, antenna, even a USB cable.

Note that GSM ("2G") coverage is mostly limited to metro areas and major towns and highways, so it won't work in many areas where only 3G coverage is available. You can check Telstra 2G coverage using the map at www.telstra.com.au/mobile-phones/coverage-networks/our-coverage/ by selecting 2G in the "Network Type" option.

Useful AT Commands

The ADH8066 GSM module is controlled using old-school AT commands. These are some handy ones to know, and your sketch can send them to the module to control it.

AT: Get attention of the module. It should respond "OK".

ATDxxxxxxxx: Dial the number.

ATA: Answer an incoming voice call.

ATH: Hang up a voice call.

AT+CSQ: Check network signal strength. Returns two numbers, comma separated. The first number is signal strength. 0 is no signal, 31 is maximum possible reading. Anything from about 12 up is OK.

AT+IPR?: Check current Interface Port Rate (baud rate of the serial port). By default the ADH8066 is set to 115200, but the ArduPhone MCU can't talk that fast while running at 8MHz so the rate has been changed to 9600.

AT+IPR=9600: Set the baud rate. The module will then restart its comms. Don't set this too fast or the ArduPhone MCU won't be able to keep up.